* TeraStation 3000 Series Firmware Updater(Mac) Ver.1.70 Name TeraStation 3000 Series Firmware Updater(Mac) Version Ver.1.70 File ts3000_series-170_fwmac.dmg.zip Size 407,604,573 Bytes Date August 16, 2016 Platform Intel Mac OS Mac OS X 10.6 or later Model TS3200D TS3400D TS3400R Copyright BUFFALO INC. Distribution Distribution ZIP archive Condition Re-distribution is not allowed. Manual Quick Setup Guide Reference Guide This product uses GPL/LGPL applicable software and your are welcome to have, modify and redistribute these source codes. Please ask our technical support people about modified GPL, applicable module and how to deliver them. You may be charged for delivery cost. [Software description] This software is TeraStation 3000 Series Firmware Update Utility to update unit firmware to Ver.1.70. If your unit firmware is Ver.1.70 or later version, you do not have to use this utility. *If the TeraStation became EM Mode, firmware update might recover the unit. [How to confirm firmware version] Select TeraStation 3000 Series from NAS Navigator2 utility search screen. The firmware version is displayed right and bottom corner in the status screen. If the unit name shown TS***-EM*** in the status screen, the TeraStation 3000 Series becomes EM (Emergency) mode. [Caution] - Please consult you local representative if you experience malfunction problem cause by firmware update. - Do not turn the unit off until complete messages appear. It might takes several minutes in the case. [How to use updater] 1. Extract the file you have downloaded. 2. Please execute "update", refer to the screen instruction. [Firmware Release Notes] Version 1.70 [2016.8.16] Bug Fixes [ImageMagick] - Modified to deal with an ImageMagick filtering vulnerability (CVE-2016-3714). [Bash] - Modified to deal with Bash programming vulnerabilities (CVE-2014-7186 and CVE-2014-7187). [OpenSSL] - Modified to deal with OpenSSL programming vulnerabilities (CVE-2016-2176, CVE-2016-2109, CVE-2016-2108, CVE-2016-2107, CVE-2016-2106, and CVE-2016-2105). [Samba] - Modified to deal with Samba programming vulnerabilities, including Badlock vulnerability (CVE-2016-2112, CVE-2016-2115, CVE-2016-2118, CVE-2016-2110, CVE-2016-2111, CVE-2015-5370, CVE-2016-2113, CVE-2016-2114, CVE-2015-5252, CVE-2015-5296, CVE-2015-5299, and CVE-2015-7560). [lighttpd] - Modified to deal with lighttpd programming vulnerabilities (CVE-2013-4559 and CVE-2014-2323). [System] - Fixed a bug where a working drive was erroneously identified as malfunctioning. - Fixed a bug where the size at "Size on disk" were displayed larger than actual size when referring the files in the TeraStation on Windows 8.1 or later. [Settings] - Fixed a bug where Settings could not be accessed. [Configuration Migration] - Fixed a bug where migrating settings from TS-XHL series failed. [Email Notifications] - Fixed a bug where blank emails was sent. - Fixed a bug where some notification emails were detected as spam by a mail server. As a countermeasure for this bug, the "Sender Address" box is added to the email notification settings page of Settings. [UPS] - Changed to have the E10 error display when the connection between the TeraStation and the UPS could not be established. [Quotas] - Fixed a bug where up to 2047 GB were allotted as the quota size. [Samba] - Fixed a bug where a trashbox folder was set to ".recycle", not "trashbox" and the created ".recycle" folder could not be deleted. The ".recycle" folder can now be deleted by clicking 'Empty Recycle Bin' from Settings after updating the firmware to this version. [NFS] - Fixed a bug where the shared folder selection window was not displayed properly when adding NFS rule if multiple shared folder with NFS enabled were created. [FTP] - Fixed a bug where the TeraStation could not be accessed via FTP after configuring access restrictions with a group that includes a specific number of members then restarted. [Microsoft Network] - Fixed a bug where domain users could not access shared folders if the group that these domain users joined is configured for access restrictions. [Network] - Fixed a bug where default gateway and DNS settings were cleared when disconnecting and reconnecting the Ethernet cable. - Fixed a bug where Wake-on-LAN did not work when disconnecting and reconnecting the power cable after the shutdown. [Services] - Fixed a bug where music files did not recognized if a subfolder that contains a space in its folder name was configured as iTunes public folder. Version 1.60 [2016.4.14] Added and Modified Features [iSCSI] - Modified to display clients connecting to the volumes when displaying the connection history. You can see it by navigating to 'Drives' - 'iSCSI' and click 'Show Active Connections' on Settings. Bug Fixes [Amazon S3] - Fixed a bug where while on the AWS Management Console, renamed or uploaded files did not appear on the TeraStations. - Fixed a bug where Amazon S3 did not work if drive 1 fails while Amazon S3 was enabled. [Others] - Fixed a bug where an error message was displayed when accessing the shared folder settings for a shared folder that has access restrictions enabled for local users. Version 1.50 [2016.2.24] Added and Modified Features [SNMP] - Modified to support SNMPv3. - Modified to support the following settings that can be acquired via SNMP protocol: Model name Firmware version Serial number Checking whether new firmware is available Showing whether the function status is enabled or disabled S.M.A.R.T. for each drive Update the MIB file on your SNMP client software to the latest version. You can download the MIB file from the Buffalo website. [OpenSSL] - Updated OpenSSL to the latest version. [Email Notifications] - Modified so that the report categories and when the email will be sent are now configurable. The current settings will be taken over by the firmware update but we recommend verifying if the function works properly after the firmware update. - S.M.A.R.T information is now available to be sent via the notification email. It can be configured from "Advanced Report Settings". Bug Fixes [Failover] - Fixed a bug where failover could not be canceled temporarily if the online update notice is present. [Email Notification] - Fixed a bug where the authentication settings were kept even if the authentication was disabled. [UPS Sync] - Fixed a bug where the E10 error occurred when specific settings were changed without connecting the UPS to the TeraStation. [Settings] - Fixed a bug where Settings could not be accessed. - Fixed a bug where the status of spare drive shows an error during bootup. - Fixed a bug where the CPU became overloaded when a test email was sent with the wrong settings. [USB Drive] - Fixed a bug where files that contain 2-byte characters in the filename could not be accessed when they were stored in NTFS-formatted USB drives. [Samba] - Fixed a bug where the access-restricted folder reserved for admin users cannot be accessed after initializing settings. Version 1.41 [2015.9.3] Bug Fixes [USB Drive] - Fixed a bug where some USB drives were not recognized by the TeraStation. Version 1.40 [2015.7.30] Bug Fixes [Configuration Management] - Fixed a bug where the Omron UPS was not recognized properly when using a D-sub 9-pin connector. [Replication] - Improved the reliability of replication. - Fixed a bug where the TeraStation became slower when accessing the replication source shared folder via FTP. - Fixed a bug where replication errors may have occurred when both virus scan and replication were enabled. [File Sharing] - Fixed a bug where any users and groups could access an access-restricted shared folder if the folder's access restriction settings were set to no access. Since this firmware update, it is modified that only admin users and groups can access the folder. Version 1.30 [2015.6.4] Added and Modified Features - TS-X series TeraStations now support the settings transfer feature. - Configuration migration now supports config files (.nas_config) that are password-protected. Bug Fixes [Configuration Migration] - Fixed a bug where protocols other than SMB were enabled on the migration target TeraStation if the migration source enabled Hidden Share and transfer its setting. - Fixed a bug where access restrictions were enabled that were disabled before transferring settings. - Fixed a bug where no error messages were displayed when the number of registrable shared folders, users, and groups reaches the maximum. - Modified the error message when the migration target TeraStation joins different domain network environment from the config file. - Modified the error message when the network disconnected while transferring settings. - Modified the error message when loading the config file failed. [Network] - Fixed a bug where access restrictions with domain users reverted to "disabled" after restarting the unit. Version 1.20 [2015.4.6] Added and Modified Features - Added feature to transfer settings from TS-HTGL/R5 series TeraStations (as of March 2015). Bug Fixes - Modified to deal with Samba programming vulnerabilities (CVE-2015-0240 and CVE-2014-0178). Version 1.16 [2015.1.14] Bug Fixes and Modified Features [Network] - Modified to deal with the OpenSSL programing vulnerabilities (CVE-2014-3567 and CVE-2014-3568) that are also know as the POODLE (SSL 3.0) vulnerability. Version 1.15 [2014.11.28] Bug Fixes [System] - Fixed a bug where a service that sent email notifications did not run. - Fixed a bug where NTP sync did not work. - Fixed a bug where user was not informed of an available online update. - Fixed a bug where S.M.A.R.T information could not be obtained. - Fixed a bug where a scheduled RAID scan did not run. - Fixed a bug where sleep timer did not run. - Fixed a bug where a scheduled backup did not run. Version 1.14 [2014.10.21] Bug Fixes and Modified Features [System] - Modified to resolve Bash programming vulnerabilities which allow remote attackers to execute arbitrary commands (CVE-2014-6271 and CVE-2014-7169). - Improved to not stop services when connecting/disconnecting USB devices. - Fixed a bug where email notification sent the same two emails after the firmware finishes updating. - Fixed a bug where port-trunked devices could not be selected for surveillance server. - Fixed a bug where some settings were not copied during failover. - Improved log messages in the SMB access logs. - Added CPU and memory utilization to system information list. [Replication] - Improved replication reliability. - Fixed a bug where the I33 message was displayed in Settings, NAS Navigator2, and on the LCD panel even though replication was not configured. Version 1.13 [2014.8.21] Bug Fixes and Modified Features [Backup and Replication] - Fixed a bug where a backup job failed if many files were backed up at once. - Fixed a bug where a backup job could not be registered if the destination folder contains a multibyte space in its folder name. - Removed the Windows backup option from the shared folder settings page. Using Windows server to back up to the TeraStation no longer requires additional configuration. - Fixed a bug where a backup job failed if a shared folder in a LVM volume is configured as a backup source. - Fixed a bug where the TeraStation on the different network could not be configured as replication target. - Fixed a bug where the TeraStation did not reply if many backup jobs were configured or deleted at the same time. - Fixed a bug where Amazon S3 folder was not displayed as a backup target. [Amazon S3] - Fixed a bug where file copying failed if many files were copied at once. - Fixed a bug where the download failed if the downloaded file is 2 GB or larger. - Fixed a bug where the connection status didn't show "Error" if connection error occurred. - Fixed a bug where invalid events were logged. [Network] - Fixed a bug where joining Active Directory may have failed. - Modified to configure IP address, subnet mask, default gateway, and DNS server from the same settings page. - Fixed a bug where changing IP address from NAS Navigator2 may not have finished properly. [FTP/FTPS] - Fixed a bug where 10 GB or larger file could not transfer via FTP. - Fixed a bug where a local user could not access the TeraStation via FTP or SFTP if the TeraStation joined a domain network. [USB] - Fixed a bug where exFAT-formatted USB hard drive disappeared if disk check was run on it. - Fixed a bug where an incorrect character may be displayed in a filename when a file is copied to an exFAT-formatted USB drive. [Update] - Fixed a bug where the guest account was enabled after the firmware was updated from version 1.11. - Fixed a bug where some settings were not restored correctly if settings were restored from the settings saved USB memory device. [Email Notification] - Improved email notifications for English, Japanese, and German languages. - Fixed a bug where the date in the email header was blank. - Fixed a bug where email notification failed if the password of email account contains specific special characters. [Others] - Modified the messages on the LCD display. - Fixed a bug where Direct Copy from the digital camera in PTP mode failed. - Fixed a bug where access limited folder could not access even if a user was allowed to access the folder. - Fixed a bug where the deleting-user event was not logged in the system log. - Fixed a bug where NTP setting could not be changed if surveillance server was enabled. - Fixed a bug where users imported from a CSV file did not join the "hdusers" group. - Improved some UI texts. Version 1.12 [2014.2.7] Bug fixes [System] - In some cases, a failed firmware update could repartition the drive(s), possibly leading to loss of user data. This problem has been resolved; the system will no longer replace user partitions. After recovery, user partitions will still be undamaged and available. Version 1.11 [2013.11.1] Added and Modified Features [System] - Antvirus scanning is now supported. [Replication] - Encrypting and compressing backup data transfers are now supported. Note: When you use these features, data transfer speeds will be slower. [NFS] - Read-only shared folders are now supported. - Async is now supported in kernel mode. Note: When you update from an older firmware, the default setting is "Async". To change it to "Sync", change NFS rules in Settings. [iSCSI] - IQN is now displayed in volume settings in Settings. Bug fixes [System] - Fixed the bug where data was not saved properly when the power was cut off right after writing the data. - Fixed the bug where settings could be changed from other computers or browsers while the firmware was being updated. - Fixed the bug where TeraStations beeped incorrectly during boot. [RAID] - Fixed the bug where RAID scanning didn't work on the first day of each month. [Backup] - Fixed the bug where backup jobs failed when multiple files were backed up. [UPS] - Fixed the bug where E10 was displayed incorrectly when an APC UPS went into test mode. Version 1.10 [2013.9.3] Modified Features [System] - TS3200D series is now supported. Bug fixes [System] - Fixed the bug where applying settings from a USB drive failed when an additional USB drive was connected to the TeraStation. - Fixed the bug where system files were corrupted and the TeraStation failed to boot when all drives were dismounted. - Fixed the bug where TeraStations failed to boot via Wake-on-LAN after unplugging the power cable without shutting the TeraStation down. - Fixed the bug where a drive error was displayed for a hot spare drive when the TeraStation was rebooted. - Fixed the bug where failover was not configured properly from the backup TeraStation's Settings. - Fixed the bug where "admin" settings couldn't be changed after settings were intialized. [Backup] - Fixed the bug where a TeraStation could be configured as the management backup target for a TeraStation on another network segment. Version 1.01 [2013.8.7] [Bug fixes] - Fixed the NTP automatic time adjustment problem after 'Management' - 'Restore/Erase' - 'Initialize TeraStation' was executed. - Fixed the problem where quota warning emails were not sent after 'Management' - 'Restore/Erase' - 'Initialize TeraStation' was executed. Version 1.00 [2013.7.1] - New release.